Keto Ply manufactures IS 710 BWP marine grade plywood at Yamunanagar and supplies it across Palanpur to dairy and agri plant wash areas, Ambaji route hotel bathrooms and Deesa and Dhanera kitchen joinery, in 6 mm to 25 mm boards.
IS 710 | BWP Grade | 6 mm to 25 mm
There is one test that separates boiling waterproof plywood from everything else, and it is not subtle: IS 710 requires the board to sit submerged in boiling water for 72 hours and still hold its plies together. BWR grade under IS 303 is boiled in cycles of eight hours; MR grade never goes near boiling water at all. Banaskantha runs dry outside and wet in the places that matter commercially. Dairy and agri facilities wash their floors and surfaces down as a matter of hygiene, hotels and dharamshalas on the Ambaji route turn bathrooms over continuously through pilgrimage season, and every home kitchen has a sink base that meets water daily whatever the climate does. Keto Marine Plywood is the BWP grade board in the Keto range, bonded with unextended phenol formaldehyde resin on a high density hardwood core, pressure treated against termite and borer, and pressed under high pressure and temperature.
Boiling water resistance, glue shear and mycological checks are run on production batches against IS 710 before the consignment is dispatched.
Unextended phenol formaldehyde resin with no fillers or extenders, which is the reason the glue line survives 72 hours of boiling rather than minutes.
Direct dispatch to Palanpur, Deesa, Dhanera, Tharad and Ambaji workshops and sites, scheduled against the site programme.
Every Keto Ply panel carries the brand's borer, fungus and anti-termite guarantee in writing.
Six things Palanpur contractors, architects and facility owners check before a panel goes into a wet area.
Request a Sample BoardIS 710 submerges the board in boiling water for 72 hours and then tests whether the plies have separated. BWR grade under IS 303 faces three cycles of eight hours; MR grade is never boiled. That gap is the whole point of specifying BWP.
No fillers, no extenders. The resin is what survives the boil, and cheapening it with extenders is the single most common way a board sold as waterproof turns out not to be.
Preservative is pressure impregnated to the retention IS 710 requires, so termite, borer and fungal protection goes through the board rather than sitting on the surface where a saw cut removes it.
IS 710 sets a wet bending strength requirement, not just a dry one, so a shelf in a sink base or a wet area still carries what it is asked to carry after it has been soaked.
Wash down areas in dairy and agri facilities, hotel and dharamshala bathrooms, and kitchen sink bases across the district. Dry furniture and storage can stay on MR grade, and we will tell you where that line falls.
Supplied from the Yamunanagar unit with dealer, workshop and project pricing for Palanpur, plus dealership openings across Banaskantha and the Abu Road corridor.
Acceptance values laid down in IS 710 (Marine Plywood - Specification), tested as per IS 1734.
| Test | Method | Requirement | What it means on site |
|---|---|---|---|
| Water Resistance | IS 1734 (Parts 4 & 5) | Submerged in boiling water for 72 hours | Three full days of boiling, against eight hour cycles for BWR grade. |
| Glue Shear Strength (wet) | IS 1734 (Part 4) | 1000 N average, 800 N minimum | The glue line still carries load while the board is soaking wet. |
| Mycological Test | IS 1734 (Part 7) | No appreciable separation at the veneer edges | The bond resists fungal attack in permanently damp locations. |
| Preservative Retention | IS 10013 | Pressure impregnated, minimum 12 kg/m³ for CCA, CCB or ACC | Protection goes through the board, so a saw cut does not expose untreated wood. |
| Wet Bending Strength | IS 1734 (Part 11) | MOR 25 N/mm² along and 15 N/mm² across, tested wet | A shelf in a sink base still carries load after it has been soaked. |
| Moisture Content | IS 1734 (Part 1) | Not less than 5% and not more than 15% | A seasoned board that will not swell and push shutters out of line. |
These are the published IS 710 acceptance criteria for marine plywood. The lot specific test report is issued with every project consignment.
Dealer supply and direct project dispatch across the district:
Not seeing your area? Keto Ply is appointing dealers across Palanpur and Banaskantha. Send a dealership enquiry and our territory manager will call back.
Share your thickness, square footage and delivery city. We will send the price list along with the current test certificate.
